With the rapid development of China's automobile industry, many families own their own private cars, but the number of garages can not meet the demand. Therefore, how to effectively prevent car theft is the most concerned issue for car owners. In recent years, science and technology have developed rapidly, and new types of car anti-theft devices combined with various new technologies have emerged. As the functions of the in-vehicle system are gradually increasing and increasing, the control of the single-chip microcomputer has become increasingly unable to meet the demand. Therefore, the use of embedded technology in automotive electronics will become inevitable.
In this paper, the embedded technology is used to develop the vehicle anti-theft device, which can enhance the control ability and improve the intelligence of the car anti-theft. On the other hand, the size of the device is reduced, the flexibility of the application of the device is increased, and an extended space is provided for further enhancing the function of the automobile electronics in the future. Due to limited space, this article only introduces the hardware circuit.
1 System hardware components The system is mainly composed of ARM embedded controller, mobile phone module, wireless remote control module, vehicle control and status detection module. The vehicle control and status detection module collects the vehicle related data to the ARM embedded controller, and the ARM embedded controller transmits it to the mobile phone module and the wireless remote control module to finally achieve the purpose of the alarm. The system principle is shown in Figure 1. 
1.1 If the control circuit generates vibration after the car thief abnormally starts the car, the vibration sensor will send the low-level effective signal to the LPC2210 , and the LPC2210 will transmit the information; one is transmitted to the alarm circuit, and the other is transmitted to the TC35. . The alarm circuit is mainly composed of an integrated block, a speaker and an electronic switch SCR. The triode or composite tube is a circuit measure commonly used to improve power. It constitutes an equivalent transistor with a large current amplification factor, and the total amplification factor is the product of the amplification factors of the two tubes. SCR is an electronic switch composed of thyristor. The capacitor and resistor form a buck and filter, which provides +3~+4 V voltage to the IC. The IC is a simulation sound alarm integrated circuit. The alarm is controlled by SCR. Once the car thief presses the wrong password, the battery current is divided into the anti-theft system, and the other is after the engine is started, after the engine is started, the output voltage of the neutral contact is passed through the differential circuit, and the thyristor SCR is triggered. The resistor is stepped down, and the voltage is applied to the power input end of the IC. The IC obtains a voltage output alarm signal, which is amplified by the composite tube to illuminate the speaker to emit a loud alarm sound. In the static state, the entire circuit does not consume power. as shown in picture 2. 
1.2 Power Interface Design The GSM module works with a voltage of 3.3 to 5 V. In the process of starting the connection transmission to the network, the Power Supply is required to provide a peak current of 2 A, and the voltage drop of the voltage cannot be greater than 400 mV. The design must take full account of the possible voltage drop. The minimum voltage must be higher than 3 V. In addition, during data transmission, the voltage fluctuation cannot be greater than 400 mV. Otherwise, the TC35 will consider the voltage to be too low and automatically shut down the module. Therefore, the power cord of the circuit should be as short as possible. If you use the battery clip as a backup power source, consider the voltage drop caused by the resistance on the motherboard and battery clip wires. In the circuit design, the power supply of the ZIF interface can be separately powered from the other power sources. The ZIF interface power supply is separately powered, and the above requirements must be ensured. The high-power device can be powered by a high-stability Switching Power Supply.
1.3 Serial Interface Design The GSM module and system processor exchange data over the serial TIU TRS 232 standard serial bus. The high level of all operations is CMOS voltage (2.65 V). Therefore, the logic level of the RS 232 conversion chip must be in the form of low voltage supply (3.3 V), and the 5 V serial port conversion chip cannot be used. In the design, MAX's MAX 3238 was selected for data conversion. The MAX 3238 is a 3.3 V logic-level serial-to-conversion chip from MAX that has the same characteristics as the popular MAX 232 except that the logic level is 3.3 V. Serial communication between the module and the processor is fully compliant with the Universal Serial Bus standard. The specific hardware interface circuit is shown in Figure 3. 
1.4 S1M card interface design The baseband processor in the GSM module has a complete SIM card interface, which is fully compliant with the ISO7816 3 standard. To ensure greater stability during SIM card interface design, the maximum length of the ZIF connector and the card pins should not exceed 200 mm. 
One issue that needs to be considered during design is the ground handling of the SIM card. Of course, there are many different ways to follow your own design habits and styles. The ultimate goal to be achieved is to have a SIM card holder with a separate ground. Therefore, a set of filter circuits is formed by one inductor and one capacitor, and a set of one side is placed on each side of the card holder to form an annular spacer, so that the SIM card and the outside maintain a relatively independent ground, and then pass through a The line connects the module interface ground to the ground of the SIM card.
1.5 Wireless remote control module design The wireless remote control function is implemented by SRWF-1 module. It is controlled by 89C51, and the information received by C51 is sent to the SRWF-1 transmitting module through the serial port. The SRWF-1 receiving module transmits the received information to the serial port through the serial port. LPC2210.
2 Conclusion <br> It has been verified by experiments that using the GSM short message-based communication method to control the car alarm system can not only greatly improve the communication reliability of the alarm system, but also the communication distance is basically unlimited, thus realizing the long-distance real-time of the user to the car. Monitoring; In addition, the system can also distinguish the urgency of the intrusion, so that users can take measures according to the situation to meet the requirements of car users for car theft, and the system is not costly and easy to promote.
This article refers to the address: http://
Type C Laptop Charger unlike traditional Laptop Charger easily gets hot and charging slowly, it offers super fast-charging via its USB-C port in very low temperature. Type C Charger Adapter is light and easy to hold.
Yidashun can offer different brands of Type C Laptop Charger, all cases similar as original one, such as for APPLE macbook pro USB C Power Adapter 29W 30W 61W 87W, for DELL 30W 45W 65W 90W PD charger, for HP/ASUS 45W 65W Type C Charger , For Toshiba/Lenovo 45W usb c charger, for Samsung 30W type c Adapter and so on. And they can be compatible with each other, for example: macbook usb c power adapter can charge DELL, ASUS, HP, LENOVO laptops, and so are other brands of laptop usb c chargers. Besides, type c laptop charger can also charge mobile phone and tablet, like APPLE usb c power adapter charger 29W, the output specifications is 14.5V 2.1A or 5.2V 2.4A, it can not only fast charge macbook pro 12 inch laptop, but also IPHONE 8 only if you change to use usb-c to Lighting Cable .
Type C Laptop Charger
Type C Laptop Charger,Macbook USB C Adapter,Type C Charger Adapter,Type C Charger For Laptop
Shenzhen Yidashun Technology Co., Ltd. , http://www.ydsadapter.com